U.S.

April 24, 2012

Enterprise flight over New York City moved to April 27

NASA managers, in coordination with Intrepid Sea, Air and Space Museum officials, tentatively are targeting April 27, for the ferry of space shuttle Enterprise from Washington Dulles International Airport to John F. Kennedy International Airport in New York.

Managers shifted the flight from April 25 to April 27 because of a large region of low pressure dominating the East Coast.

NASA’s 747 Shuttle Carrier Aircraft with Enterprise mounted atop will fly at a relatively low altitude over various parts of the New York City metropolitan area on Friday. The aircraft is expected to fly near a variety of landmarks, including the Statue of Liberty and Intrepid. After the flyover is complete, the SCA will land at JFK.

The Federal Aviation Administration is coordinating the flight, which is scheduled to occur between 9:30 and 11:30 a.m., EDT, weather permitting. The exact route and timing depend on weather and operational constraints.

Enterprise was mated to the SCA April 21 morning and covers were fitted over the shuttle’s vent doors to prevent rain intrusion while the vehicle awaits its transfer from Dulles. The covers will be removed before flight.

During the weeks following the arrival, Enterprise will be demated from the 747 and placed on a barge that will move by tugboat up the Hudson River to Intrepid in June. The shuttle will be lifted by crane and placed on the flight deck of the Intrepid, where it will be on exhibit to the public starting this summer in a temporary climate-controlled pavilion. The Intrepid continues to work on a permanent exhibit facility to showcase Enterprise that will enhance the museum’s space-related exhibits and education curriculum.

If the flight is postponed for any reason, an additional notice will be released.

 

For more information about NASA’s transfer of space shuttles to museums, visit http://www.nasa.gov/transition.

 




All of this week's top headlines to your email every Friday.


 
 

 

Headlines September 2, 2014

News: Debris yields clues that pilot never ejected - When investigators were finally able to safely enter the crash site of an F-15C “Eagle” fighter jet on the afternoon of Aug. 27, they made a grim discovery that concluded more than 30 hours of searching – the pilot never managed to eject from the aircraft.  ...
 
 

News Briefs September 2, 2014

Pentagon: Iraq operations cost $560 million so far U.S. military operations in Iraq, including airstrikes and surveillance flights, have cost about $560 million since mid-June, the Pentagon said Aug. 29. Rear Adm. John Kirby, the Pentagon press secretary, said the average daily cost has been $7.5 million. He said it began at a much lower...
 
 

Unmanned aircraft partnership reaches major milestone

A team of research students and staff from Warsaw University of Technology have successfully demonstrated the first phase of flight test and integration of unmanned aircraft platforms with an autonomous mission control system. The demonstration marks a significant milestone in a partnership between the university and Lockheed Martin that began earlier this year. This is...
 

 

Raytheon delivers first Block 2 Rolling Airframe Missiles to US Navy

Raytheon delivered the first Block 2 variant of its Rolling Airframe Missile system to the U.S. Navy as part of the company’s 2012 Low Rate Initial Production contract. RAM Block 2 is a significant performance upgrade featuring enhanced kinematics, an evolved radio frequency receiver, and an improved control system. “As today’s threats continue to evolve,...
 
 
Courtesy photograph

Two Vietnam War Soldiers, one from Civil War to receive Medal of Honor

U.S. Army graphic Retired Command Sgt. Maj. Bennie G. Adkins and former Spc. 4 Donald P. Sloat will receive the Medal of Honor for actions in Vietnam. The White House announced Aug. 26 that Retired Command Sgt. Maj. Bennie G. A...
 
 

Sparks fly as NASA pushes limits of 3-D printing technology

NASA has successfully tested the most complex rocket engine parts ever designed by the agency and printed with additive manufacturing, or 3-D printing, on a test stand at NASA’s Marshall Space Flight Center in Huntsville, Ala. NASA engineers pushed the limits of technology by designing a rocket engine injector – a highly complex part that...
 




0 Comments


Be the first to comment!


Leave a Reply

Your email address will not be published. Required fields are marked *

You may use these HTML tags and attributes: <a href="" title=""> <abbr title=""> <acronym title=""> <b> <blockquote cite=""> <cite> <code> <del datetime=""> <em> <i> <q cite=""> <strike> <strong>