Business

May 16, 2012

General Dynamics unveils new medium-caliber machine gun

General Dynamics Armament and Technical Products, a business unit of General Dynamic, unveiled a next-generation Lightweight Medium Machine Gun at the Joint Armaments Conference in Seattle, Wash., May 15.

Identifying an unmet warfighter need, General Dynamics Armament and Technical Products conducted its own research and development program to develop the LWMMG in just over one year. The weapon is designed for low-cost production and for maximum effectiveness at the small unit level, where weight and lethality are decisive factors.

“The LWMMG is an affordable weapon that closes a current operational gap, providing .50 caliber-like firepower in range and effect at the same weight and size of currently fielded 7.62mm machine guns,” said Steve Elgin, vice president and general manager of armament systems for General Dynamics Armament and Technical Products. “Weighing in at 24 pounds and featuring a fully collapsible stock, the LWMMG offers superior mobility and portability in both mounted and dismounted operations.”

General Dynamics’ LWMMG also offers a distinct advantage in both extended and close-in fighting by using the highly efficient .338 Norma Magnum cartridge for increased accuracy and lethality out to 1,700 meters, a distance currently gapped in the operational capabilities of warfighters.

“By employing the larger .338 NM round, the LWMMG delivers twice the range and dramatically increases lethality above the 7.62 round,” said Elgin. “In addition, the LWMMG goes beyond providing suppressive fire and gives warfighters the ability to attack point targets at significantly extended ranges.”

The LWMMG has a firing rate of 500 rounds per minute, a maximum range of 5,642 meters, and is equipped with quick-change barrel technology. In addition to use by dismounted infantry and on ground vehicles, the weapon can be used as the armament system aboard helicopters and littoral craft, providing greater range and effectiveness for those platforms.

“The LWMMG is a well-designed machine gun ideally suited to provide long-range lethality to U.S. and allied forces,” Elgin said.




All of this week's top headlines to your email every Friday.


 
 

 

Headlines September 2, 2014

News: Debris yields clues that pilot never ejected - When investigators were finally able to safely enter the crash site of an F-15C “Eagle” fighter jet on the afternoon of Aug. 27, they made a grim discovery that concluded more than 30 hours of searching – the pilot never managed to eject from the aircraft.  ...
 
 

News Briefs September 2, 2014

Pentagon: Iraq operations cost $560 million so far U.S. military operations in Iraq, including airstrikes and surveillance flights, have cost about $560 million since mid-June, the Pentagon said Aug. 29. Rear Adm. John Kirby, the Pentagon press secretary, said the average daily cost has been $7.5 million. He said it began at a much lower...
 
 

Unmanned aircraft partnership reaches major milestone

A team of research students and staff from Warsaw University of Technology have successfully demonstrated the first phase of flight test and integration of unmanned aircraft platforms with an autonomous mission control system. The demonstration marks a significant milestone in a partnership between the university and Lockheed Martin that began earlier this year. This is...
 

 

Raytheon delivers first Block 2 Rolling Airframe Missiles to US Navy

Raytheon delivered the first Block 2 variant of its Rolling Airframe Missile system to the U.S. Navy as part of the company’s 2012 Low Rate Initial Production contract. RAM Block 2 is a significant performance upgrade featuring enhanced kinematics, an evolved radio frequency receiver, and an improved control system. “As today’s threats continue to evolve,...
 
 
Courtesy photograph

Two Vietnam War Soldiers, one from Civil War to receive Medal of Honor

U.S. Army graphic Retired Command Sgt. Maj. Bennie G. Adkins and former Spc. 4 Donald P. Sloat will receive the Medal of Honor for actions in Vietnam. The White House announced Aug. 26 that Retired Command Sgt. Maj. Bennie G. A...
 
 

Sparks fly as NASA pushes limits of 3-D printing technology

NASA has successfully tested the most complex rocket engine parts ever designed by the agency and printed with additive manufacturing, or 3-D printing, on a test stand at NASA’s Marshall Space Flight Center in Huntsville, Ala. NASA engineers pushed the limits of technology by designing a rocket engine injector – a highly complex part that...
 




0 Comments


Be the first to comment!


Leave a Reply

Your email address will not be published. Required fields are marked *

You may use these HTML tags and attributes: <a href="" title=""> <abbr title=""> <acronym title=""> <b> <blockquote cite=""> <cite> <code> <del datetime=""> <em> <i> <q cite=""> <strike> <strong>