Business

June 26, 2012

Northrop Grumman to modify E-6B with high-speed, secure networking and communications

The U.S. Navy has awarded Northrop Grumman a $44.3 million contract to integrate high-speed, secure communications and networking systems on an E-6B Mercury aircraft, part of the Take Charge and Move Outstrategic communications relay mission.

Navy E-6B TACAMO aircraft provide survivable and reliable airborne command, control and communications between the president of the United States, secretary of Defense, and U.S. strategic and nonstrategic forces.

With the Block II Modification, the E-6B aircraft will be able to connect to secure U.S. Department of Defense networks at high data rates while still in flight. The upgrade will enable users on board the aircraft to access mission-essential, near-real-time information from worldwide sources without impacting the operational performance of the aircraft.

“Northrop Grumman’s innovative approach to integration allows the government to rapidly field emerging technologies for vital defense missions such as TACAMO within existing budget constraints,” said Claude Hashem, vice president of network communications systems for Northrop Grumman Information Systems. “The Block II Modification will provide the E-6B community with superior networking capability that enables a significant increase in operational capability.”

Northrop Grumman will design and produce networking and communications systems, first integrating the systems into the E-6B Systems Integration Laboratory and then on a single E-6B aircraft. Under the contract, awarded by the Naval Air Systems Command, Northrop Grumman will also provide testing, logistics and training to support operational fielding.

The Navy intends to field the enhanced capability to the entire fleet of E-6B aircraft through a follow-on contract. Navy E-6B aircraft are used to conduct both the TACAMO and U.S. Strategic Command Aiirborne Command Post missions.




All of this week's top headlines to your email every Friday.


 
 

 

Headlines September 2, 2014

News: Debris yields clues that pilot never ejected - When investigators were finally able to safely enter the crash site of an F-15C “Eagle” fighter jet on the afternoon of Aug. 27, they made a grim discovery that concluded more than 30 hours of searching – the pilot never managed to eject from the aircraft.  ...
 
 

News Briefs September 2, 2014

Pentagon: Iraq operations cost $560 million so far U.S. military operations in Iraq, including airstrikes and surveillance flights, have cost about $560 million since mid-June, the Pentagon said Aug. 29. Rear Adm. John Kirby, the Pentagon press secretary, said the average daily cost has been $7.5 million. He said it began at a much lower...
 
 

Unmanned aircraft partnership reaches major milestone

A team of research students and staff from Warsaw University of Technology have successfully demonstrated the first phase of flight test and integration of unmanned aircraft platforms with an autonomous mission control system. The demonstration marks a significant milestone in a partnership between the university and Lockheed Martin that began earlier this year. This is...
 

 

Raytheon delivers first Block 2 Rolling Airframe Missiles to US Navy

Raytheon delivered the first Block 2 variant of its Rolling Airframe Missile system to the U.S. Navy as part of the company’s 2012 Low Rate Initial Production contract. RAM Block 2 is a significant performance upgrade featuring enhanced kinematics, an evolved radio frequency receiver, and an improved control system. “As today’s threats continue to evolve,...
 
 
Courtesy photograph

Two Vietnam War Soldiers, one from Civil War to receive Medal of Honor

U.S. Army graphic Retired Command Sgt. Maj. Bennie G. Adkins and former Spc. 4 Donald P. Sloat will receive the Medal of Honor for actions in Vietnam. The White House announced Aug. 26 that Retired Command Sgt. Maj. Bennie G. A...
 
 

Sparks fly as NASA pushes limits of 3-D printing technology

NASA has successfully tested the most complex rocket engine parts ever designed by the agency and printed with additive manufacturing, or 3-D printing, on a test stand at NASA’s Marshall Space Flight Center in Huntsville, Ala. NASA engineers pushed the limits of technology by designing a rocket engine injector – a highly complex part that...
 




0 Comments


Be the first to comment!


Leave a Reply

Your email address will not be published. Required fields are marked *

You may use these HTML tags and attributes: <a href="" title=""> <abbr title=""> <acronym title=""> <b> <blockquote cite=""> <cite> <code> <del datetime=""> <em> <i> <q cite=""> <strike> <strong>