Tech

August 21, 2012

Two hurricane Global Hawks, two sets of instruments

NASA Goddard’s Cloud Physics Lidar electronics are installed in the upper area of NASA’s Global Hawk unmanned aircraft just in front of the aircraft’s communications antenna.

NASA’s Hurricane Severe Storm Sentinel Mission, or HS3, will be studying hurricanes at the end of the summer, and there will be two high-altitude, long-duration unmanned aircraft with different instruments flying over the storms.

The unmanned aircraft, dubbed “severe storm sentinels,” are operated by pilots located in ground control stations at NASA’s Wallops Flight Facility in Wallops Island, Va., and NASA’s Dryden Flight Center on Edwards Air Base, Calif. The NASA Global Hawk is well-suited for hurricane investigations because it can over-fly hurricanes at altitudes greater than 60,000 feet with flight durations of up to 28 hours.

Using unmanned aircraft has many advantages. Hurricanes present an extreme environment that is difficult to sample. They cover thousands of square miles in area, and can also extend up to 50,000 feet in altitude. Second, they involve very high winds, turbulence and heavy precipitation. Third, ground conditions (high winds that create heavy seas or blowing material) make surface observations difficult.

Technicians prepare to install the High-Altitude Imaging Wind and Rain Profiler, or HIWRAP, on the underside of a NASA Global Hawk. HIWRAP is one of the science instruments being carried by the remotely operated high-altitude aircraft during the Hurricane and Severe Sentinel missions.

“Several NASA centers are joining federal and university partners in the Hurricane and Severe Storm Sentinel airborne mission targeted to investigate the processes that underlie hurricane formation and intensity change in the Atlantic Ocean basin,” said Scott Braun, principal investigator for the HS3 Mission and research meteorologist at NASA’s Goddard Space Flight Center in Greenbelt, Md.

Two NASA Global Hawks that will be flying during the HS3 mission. Each will have different payloads, or collections of instruments aboard. Necessary observations are winds, temperature, humidity (water), precipitation, and aerosol (particle) profiles from the surface to the lower stratosphere.

NASA Goddard’s Lihau Li, left, and Gerry Heymsfield adjust the High-Altitude Imaging Wind and Rain Profiler prior to its installation on NASA’s Global Hawk for the upcoming hurricane study.

NASA’s Global Hawk No. 871 cruises over low cloud layers above the Dryden Flight Research Center on Edwards Air Force Base, Calif. This was the first Global Hawk built in the original Advanced Concept Technology Demonstration program, joining NASA’s other Global Hawk, No. 872, for high-altitude, long-endurance environmental science missions.

The first Global Hawk payload, installed in aircraft No. 872, will consist of three instruments. That payload is for sampling the environment that hurricanes are embedded within. A laser system called Cloud Physics Lidar developed at NASA Goddard will be located in the Global Hawk’s nose. CPL measures cloud structure and aerosols such as dust, sea salt particles, smoke particles by bouncing laser light off of those particles and clouds. An infrared instrument called the Scanning High-resolution Interferometer Sounder or S-HIS from the University of Wisconsin in Madison, will be located in the belly of the Global Hawk. It can be used to remotely measure or remotely sense the temperature and water vapor vertical profile along with the sea surface temperature and some cloud properties. A dropsonde system from the National Center for Atmospheric Research and National Oceanic and Atmospheric Administration will be located in the tail of the aircraft. The dropsonde system ejects small sensors tied to parachutes that drift down through the storm measuring winds, temperature and humidity.

Global Hawk No. 871 will also carry a payload of three instruments. That Global Hawk’s prime responsibility is to sample the cores of hurricanes. A microwave system called the High-Altitude MMIC Sounding Radiometer or HAMSR, created by NASA’s Jet Propulsion Laboratory in Pasadena, Calif., will be located in the aircraft’s nose. HAMSR measures temperature, water vapor, and vertical precipitation profiles.

A radar system called the High-altitude Imaging Wind & Rain Airborne Profiler or HIWRAP from NASA Goddard will be located in the second (No. 871) Global Hawk’s belly. It is similar to a ground radar system but pointed downward. HIWRAP measures cloud structure and winds. The Hurricane Imaging Radiometer (HIRAD) from NASA’s Marshall Space Flight Center in Huntsville, Ala., will be located in the aircraft’s tail section. HIRAD measures microwave radiation emitted from the surface and atmosphere. The HIRAD observations yield surface wind speeds and rain rates.

Both Global Hawks will be flying out of NASA Wallops Flight Facility in September, the peak month for the Atlantic Hurricane Season.

 




All of this week's top headlines to your email every Friday.


 
 

 

ONR features technology for Marines of future

From virtual training to laser weapons, the Office of Naval Research is showcasing a range of technologies at Modern Day Marine exposition Sept. 23-25 that will prepare Marines as they continue to face an increasingly complex security landscape. ONR program officers will be in booth no. 2305 during the event, held at Marine Corps Base...
 
 
University of Alaska-Fairbanks photograph by Chris Larsen

NASA airborne campaigns focus on climate impacts in Arctic

University of Alaska-Fairbanks photograph by Chris Larsen Changes in more than 130 Alaskan glaciers are being surveyed by scientists at the University of Alaska-Fairbanks in a DHC-3 Otter as part of NASA’s multi-year Oper...
 
 
NASA/SSAI photograph by Edward Winstead

ACCESS II confirms jet biofuel burns cleaner

NASA/ORAU photograph by Richard Moore NASA’s DC-8 research aircraft leads one of the ACCESS II sampler aircraft across the early morning California sky.   Flying high above the California desert, NASA researchers rec...
 

 

Sparks fly as NASA pushes limits of 3-D printing technology

NASA has successfully tested the most complex rocket engine parts ever designed by the agency and printed with additive manufacturing, or 3-D printing, on a test stand at NASA’s Marshall Space Flight Center in Huntsville, Ala. NASA engineers pushed the limits of technology by designing a rocket engine injector – a highly complex part that...
 
 
NASA photograph by David Alexander

NASA MQ-9 remotely piloted aircraft completes visual, radar mission in Hawaii

NASA photograph “Ikhana,” NASA’s MQ-9 remotely piloted research aircraft, carries a maritime radar in a specialized centerline pod during a flight to check out systems prior to the aircraft’s deployment ...
 
 
NASA photograph by Tom Tschida

NASA Armstrong’s space shuttle Mate-Demate Device coming down

NASA photograph by Tom Tschida The space shuttle Mate-Demate Device that stood as an iconic symbol of NASA’s now-concluded Space Shuttle Program at NASA Armstrong Flight Research Center for 38 years is being dismantled af...
 




0 Comments


Be the first to comment!


Leave a Reply

Your email address will not be published. Required fields are marked *

You may use these HTML tags and attributes: <a href="" title=""> <abbr title=""> <acronym title=""> <b> <blockquote cite=""> <cite> <code> <del datetime=""> <em> <i> <q cite=""> <strike> <strong>