Tech

November 5, 2012

X-48 Blended Wing Body Research aircraft makes 100th test flight

The upgraded X-48C version of Boeing’s Blending Wing Body subscale research aircraft banks over Rogers Dry Lake near “Contractors’ Row” at Edwards Air Force Base during a test flight Oct. 16, 2012. Combined with the earlier X-48B version, the X-48 technology demonstrator has now flown 100 test missions, more than any other single unmanned X-plane.

The Boeing X-48 Blended Wing Body subscale research aircraft made its 100th flight in late October at NASA’s Dryden Flight Research Center at Edwards Air Force Base, Calif.

The milestone occurred Oct. 30 when the unmanned X-48C aircraft was flown on two separate 25-minute flights – the seventh and eighth flights for the X-48C since it began flying Aug. 7. Between 2007 and 2010, the aircraft, then in the X-48B configuration, made 92 flights.

“Once again, working closely with NASA, we have been pleased to pass another flight-test milestone in our work to explore and validate the aerodynamic characteristics and efficiencies of the Blended Wing Body concept,” said Boeing X-48 project manager Mike Kisska of Boeing Research and Technology. “We are thrilled by the continued success of our flight testing and the useful data that we have collected during the first eight X-48C flights,” added Heather Maliska, NASA Dryden’s X-48C project manager.
Kisska noted that with 100 test flights flown, the X-48 has far surpassed the previous record of 40 flights performed by a single unmanned X-plane, held by one of the X-45A Joint Unmanned Combat Aircraft technology demonstrators, also developed by Boeing.

The X-48 is a scale model of a heavy-lift, subsonic aircraft that forgoes the conventional tube-and-wing airplane design in favor of a triangular aircraft that effectively merges the vehicle’s wing and body. Boeing and NASA believe the blended or hybrid wing body concept offers the long-term potential of significantly greater fuel efficiency and reduced noise.

Boeing’s blended wing body program manager Bob Liebeck said earlier flight tests of the X-48B proved that a blended wing body aircraft can be controlled as effectively as a conventional tube-and-wing aircraft during takeoffs and landings and other low-speed segments of the flight regime. With the X-48C, the team has been evaluating the impact of noise-shielding concepts on low-speed flight characteristics.

The X-48C, which was modified from the previous X-48B version, is configured with two small 89-pound-thrust turbojet engines instead of the three 50-pound-thrust engines on the B-model. The wingtip winglets on the X-48B have been relocated inboard next to the engines on the C-model, effectively turning them into twin tails, and the aft deck was extended about two feet at the rear.

The Boeing-NASA team expects to fly the X-48C approximately 20 more times by the end of this year.




All of this week's top headlines to your email every Friday.


 
 

 
University of Rhode Island photograph by Tom Glennon

NASA kicks off field campaign to probe ocean ecology, carbon cycle

University of Rhode Island photograph by Tom Glennon The Research Vessel Endeavor is the floating laboratory that scientists will use for the ocean-going portion of the SABOR field campaign this summer. NASA embarks this week o...
 
 
NASA photograph by Carla Thomas

NASA’s high-flying laser altimeter to check out summer sea ice, more

NASA photograph by Carla Thomas This summer, the Multiple Altimeter Beam Experimental Lidar, or MABEL, will fly above Alaska and the Arctic Ocean on one of NASA’s ER-2 high-altitude aircraft. Sea ice in summer looks dramatica...
 
 
SOFIA

Outer space to inner space: SOFIA inside Lufthansa Technik hangar

NASA photograph by Jeff Doughty NASA’s Stratospheric Observatory for Infrared Astronomy is shown inside the Lufthansa Technik hangar in Hamburg, Germany where it is beginning its decadal inspection. Flight, aircraft maint...
 

 
NASA photograph by Tony Landis

New life for an old bird: NASA’s F-15B test bed gets new engines

NASA photograph NASA’s F-15B flight research test bed carries shuttle thermal insulation panels on its underbelly during a research flight in 2005. NASA Armstrong’s F-15B aeronautics research test bed, a workhorse at th...
 
 
NASA photograph by Tom Tschida

Towed glider benefits from center’s new 3-D printer capability

NASA photograph by Tom Tschida The major components of NASA Armstrong’s new high-resolution 3-D additive manufacturing printer occupy a shelf in the center’s subscale aircraft research lab. Robert “Red” ...
 
 
NASA photograph by Emmett Given

NASA completes testing on 3-D printer

NASA photograph by Emmett Given United Space Alliance engineer Cynthia Azzarita, left, and Boeing Company engineer Chen Deng, members of the Human Factors Integration Team at NASA’s Johnson Space Center, conduct a “...
 




0 Comments


Be the first to comment!


Leave a Reply

Your email address will not be published. Required fields are marked *

You may use these HTML tags and attributes: <a href="" title=""> <abbr title=""> <acronym title=""> <b> <blockquote cite=""> <cite> <code> <del datetime=""> <em> <i> <q cite=""> <strike> <strong>