Tech

February 8, 2013

NASAs Super-Tiger balloon breaks records while collecting data

A large NASA science balloon has broken two flight duration records while flying over Antarctica carrying an instrument that detected 50 million cosmic rays.

The Super Trans-Iron Galactic Element Recorder (Super-TIGER) balloon launched at 3:45 p.m. EST, Dec. 8 from the Long Duration Balloon site near McMurdo Station. It spent 55 days, 1 hour, and 34 minutes aloft at 127,000 feet, more than four times the altitude of most commercial airliners, and was brought down to end the mission on Feb. 1. Washington University of St. Louis managed the mission.

On Jan. 24, the Super-TIGER team broke the record for longest flight by a balloon of its size, flying for 46 days. The team broke another record Feb. 1 after landing by becoming the longest flight of any heavy-lift scientific balloon, including NASA’s Long Duration Balloons. The previous record was set in 2009 by NASA’s Super Pressure Balloon test flight at 54 days, 1 hour, and 29 minutes.

“Scientific balloons give scientists the ability to gather critical science data for a long duration at a very low relative cost,” said Vernon Jones, NASA’s Balloon Program Scientist.

Super-TIGER flew a new instrument for measuring rare elements heavier than iron among the flux of high-energy cosmic rays bombarding Earth from elsewhere in our Milky Way galaxy. The information retrieved from this mission will be used to understand where these energetic atomic nuclei are produced and how they achieve their very high energies.

The balloon gathered so much data it will take scientists about two years to analyze it fully.

“This has been a very successful flight because of the long duration, which allowed us to detect large numbers of cosmic rays,” said Dr. Bob Binns, principal investigator of the Super-TIGER mission. “The instrument functioned very well.”

The balloon was able to stay aloft as long as it did because of prevailing wind patterns at the South Pole. The launch site takes advantage of anticyclonic, or counter-clockwise, winds circulating from east to west in the stratosphere there. This circulation and the sparse population work together to enable long-duration balloon flights at altitudes above 100,000 feet.

The National Science Foundation (NSF) Office of Polar Programs manages the U.S. Antarctic Program and provides logistic support for all U.S. scientific operations in Antarctica. NSF’s Antarctic support contractor supports the launch and recovery operations for NASA’s Balloon Program in Antarctica. Mission data were downloaded using NASA’s Tracking and Data Relay Satellite System.




All of this week's top headlines to your email every Friday.


 
 

 
University of Rhode Island photograph by Tom Glennon

NASA kicks off field campaign to probe ocean ecology, carbon cycle

University of Rhode Island photograph by Tom Glennon The Research Vessel Endeavor is the floating laboratory that scientists will use for the ocean-going portion of the SABOR field campaign this summer. NASA embarks this week o...
 
 
NASA photograph by Carla Thomas

NASA’s high-flying laser altimeter to check out summer sea ice, more

NASA photograph by Carla Thomas This summer, the Multiple Altimeter Beam Experimental Lidar, or MABEL, will fly above Alaska and the Arctic Ocean on one of NASA’s ER-2 high-altitude aircraft. Sea ice in summer looks dramatica...
 
 
SOFIA

Outer space to inner space: SOFIA inside Lufthansa Technik hangar

NASA photograph by Jeff Doughty NASA’s Stratospheric Observatory for Infrared Astronomy is shown inside the Lufthansa Technik hangar in Hamburg, Germany where it is beginning its decadal inspection. Flight, aircraft maint...
 

 
NASA photograph by Tony Landis

New life for an old bird: NASA’s F-15B test bed gets new engines

NASA photograph NASA’s F-15B flight research test bed carries shuttle thermal insulation panels on its underbelly during a research flight in 2005. NASA Armstrong’s F-15B aeronautics research test bed, a workhorse at th...
 
 
NASA photograph by Tom Tschida

Towed glider benefits from center’s new 3-D printer capability

NASA photograph by Tom Tschida The major components of NASA Armstrong’s new high-resolution 3-D additive manufacturing printer occupy a shelf in the center’s subscale aircraft research lab. Robert “Red” ...
 
 
NASA photograph by Emmett Given

NASA completes testing on 3-D printer

NASA photograph by Emmett Given United Space Alliance engineer Cynthia Azzarita, left, and Boeing Company engineer Chen Deng, members of the Human Factors Integration Team at NASA’s Johnson Space Center, conduct a “...
 




0 Comments


Be the first to comment!


Leave a Reply

Your email address will not be published. Required fields are marked *

You may use these HTML tags and attributes: <a href="" title=""> <abbr title=""> <acronym title=""> <b> <blockquote cite=""> <cite> <code> <del datetime=""> <em> <i> <q cite=""> <strike> <strong>