Tech

June 12, 2013

Army researchers chase helicopter performance gains

Army photograph by Capt. Jesse Paulsboe

A new study by Army researchers looks at inserting carbon nanotubes into the structural design of helicopter rotor blades to improve performance. Pictured here, an AH-64 Apache rises from behind a hill during a training exercise at Yakima Training Center, Wash. The AH-64E Guardian replaces the AH-64D “Longbow” and integrates more powerful engines, improved rotor blade technology and advanced electronics.

A new study by Army researchers looks at inserting carbon nanotubes into the structural design of helicopter rotor blades to improve performance.

The U.S. Army Research, Development and Engineering Command’s research laboratory hopes this approach could lead to the design and fabrication of the next generation of rotor blades and fixed wings.

Bryan Glaz, Ph.D., Jaret Riddick, Ph.D., and Ed Habtour, research engineers from the U.S. Army Research Laboratory Vehicle Technology Directorate, lead this effort.

Glaz and a team of structural, mechanical and aerospace engineers are embedding carbon nanotubes inside the composite matrix, resin material throughout the blade, and in specific locations like near the hub, which he said “gives more bang for the buck.”

“Especially in conflicts like Afghanistan, it really highlighted the deficiencies of the DOD current fleet in terms of payload capacity, speeds in supporting the warfighter and a big thing for the Department of Defense was the maintenance and cost,” Glaz said. “They can’t be sitting in a maintenance bay because if they’re in a maintenance bay, they’re not out there supporting the warfighter.”

Rotor structural dynamics can be inherently unstable. Structural design and the aeromechanics of rotorcraft flight can limit forward flight and maneuver capabilities and potentially lead to catastrophic structural failures in takeoff and landing conditions.

There is a tradeoff between rotor blades designed to transmit low vibrations to the aircraft and blades designed for stability, Glaz said. Blades with good stability characteristics tend to transmit high vibratory loads to the aircraft, and the high vibratory loads of rotorcraft are a major source of maintenance, repair and logistics burden associated with the DOD vertical-lift fleet.

The reverse is also true – blade designs with to low vibration tend to have structural dynamic stability issues that tend to limit the performance of the aircraft. This trade-off prevents the development of next-generation radical design concepts with substantially improved payload, speed, range and cost.

“Our goal is to eliminate the trade-off,” Glaz said. “We would like to be able to design blades that transmit low loads yet still have good stability characteristics.”

With the carbon nanotubes inside and inherent to that structure, researchers expect to enhance energy dissipation through friction at the nanotube-matrix interface and improve damping.

“We believe this improvement in damping can be exploited to so drastically improve stability without adding weight or mechanical complexity that rotorcraft designs never considered possible may become reality,” Glaz said.

Army researchers turned to recent scientific publications that indicate that carbon nanotubes can effectively dissipate energy for small scale samples. They’re venturing into uncharted research territory by investigating how much of the energy dissipation mechanism can be achieved when the carbon nanotubes are used to damp dynamic modes of actual structures as opposed to small laboratory samples.

These components would be similar to existing structures in the sense that the composite structures would still consist of a matrix with fiber reinforcement.

“In our case though, the matrix would be completely different since it would have carbon nanotubes inserted throughout,” Glaz said. “The nanotube enhanced matrix would provide the damping while fibers would still be used for strength and stiffness of the structure.”

In the future, the next-generation fleet will carry greater payloads and fly unimagined speeds with very low maintenance considerations, researchers said.

 




All of this week's top headlines to your email every Friday.


 
 

 

Headlines October 24, 2014

News: U.S., South Korea delay transfer of wartime control - The U.S. and South Korea have delayed transferring wartime operational control of allied forces by taking on a “conditions-based approach” and scrapping the previously set deadline of 2015.   Business: Exclusive: Lockheed, Pentagon reach $4 billion deal for more F-35 jets - Lockheed Martin and U.S. defense...
 
 

News Briefs October 24, 2014

French moving troops toward Libyan border A top French military official says the country is moving troops toward the Libyan border within weeks and, along with U.S. intelligence, is monitoring al Qaeda arms shipments to Africa’s Sahel region. A French base will go up within weeks in a desert outpost just a hundred kilometers (60...
 
 
Navy photograph

Navy to commission submarine North Dakota

Navy photograph The PCU North Dakota (SSN 784) during bravo sea trials. The crew performed exceptionally well on both alpha and bravo sea trials. The submarine North Dakota is the 11th ship of the Virginia class, the first U.S....
 

 

Boeing announces SF Airlines order for Boeing converted freighters

Boeing announced Oct. 23 that SF Airlines has placed an order for an undisclosed number of 767-300ER passenger-to-freighter conversions (Boeing Converted Freighters). SF Airlines, a subsidiary of Shenzhen, China-based delivery services company SF Express, will accept its first redelivered 767 in the second half of 2015. “SF Express aims to become China’s most respected and...
 
 
LM-C130

Another Super Herc Little Rock Rollin’

  Lockheed Martin delivered another C-130J Super Hercules to the 61st Airlift Squadron at Little Rock Air Force Base, Ark., Oct. 23. Little Rock AFB’s new C-130J was ferried from the Lockheed Martin Aeronautics facility ...
 
 

United Technologies beats third quarter profit expectations

United Technologies Corp. Oct. 23 reported third-quarter profit of $1.85 billion as sales increased across all its businesses and the aerospace giant reported favorable tax settlements. The Hartford, Conn.,-based company said it had profit of $2.04 per share and earnings, adjusted for non-recurring gains, came to $1.82 per share. The results topped Wall Street expectations,...
 




0 Comments


Be the first to comment!


Leave a Reply

Your email address will not be published. Required fields are marked *

You may use these HTML tags and attributes: <a href="" title=""> <abbr title=""> <acronym title=""> <b> <blockquote cite=""> <cite> <code> <del datetime=""> <em> <i> <q cite=""> <strike> <strong>